IMPROVEMENTS ON ZINC-OXIDE - EUGENOL DENTAL CEMENT BY POLYMERIZATION AND MODIFICATION OF EUGENOL AND ISOEUGENOL

LDR 03460nam a22003497 4500
001 002157210
003 MiAaHDL
005 20240704000000.0
006 m d
007 cr bn ---auaua
007 hd|afb|||baca
008 900809c19811981miu|||| |b||| 00|00|eng d
035 ‡a(MiU)990021572100106381
035 ‡asdr-miu.990021572100106381
035 ‡z(MiU)MIU01000000000000002157210-goog
035 ‡a(OCoLC)68291109
035 ‡a(UMI)08125206
035 ‡z(MiU)Aleph002157210
040 ‡aUMI ‡cUMI ‡dMiU
099 ‡aUMI diss--UM
100 1 ‡aSTANNARD, JAN GREGORY
245 1 0 ‡aIMPROVEMENTS ON ZINC-OXIDE - EUGENOL DENTAL CEMENT BY POLYMERIZATION AND MODIFICATION OF EUGENOL AND ISOEUGENOL.
260 ‡c1981.
300 ‡a195 p.
502 ‡aDISSERTATION (PH.D.)--THE UNIVERSITY OF MICHIGAN
510 4 ‡aDissertation Abstracts International, ‡c42-06B, p. 2297, AAF8125206
520 8 ‡aCell culture toxicity measurements were conducted at 18 hour exposures. Cements containing H(,2)PtCl(,6) were equal in "toxicity" to ZOE cements. A toxic response was elicited by H(,2)PtCl(,6). Eugenol alone was "toxic" at 0.081 mM. Isoeugenol was equal in "toxicity" to eugenol from 0.081- 1.399 mM. Isoeugenol cements were equal in "toxicity" to ZOE cements.
520 8 ‡apre-mixing.
520 8 ‡aA "multifunctional" chelation approach to ZOE setting was also evaluated. When 2,5-dimethoxyhydroquinone, I, was mixed at its melting point with zinc oxide, a CS of 48.3 MN/m('2) was obtained which was compared to 36.5 MN/m('2) for an unmodified cement. Pre-mixing I or 5,5'-methylene disalicylic acid, II, with zinc oxide at their melting points before mixing with eugenol increased the CS to I-24.1 and II-26.8 compared to 9.3 MN/m('2). Formation of a zinc eugenolate-like structure resulted from this
520 8 ‡aIsoeugenol when mixed with zinc oxide showed a CS of 30.6 MN/m('2) compared to 9.3 MN/m('2) for a comparable ZOE cement. Polymerization of isoeugenol with H(,2)PtCl(,6) and acetic acid, with zinc oxide increased the CS to 57.38 MN/m('2). The control cement was rubber-like at two weeks.
520 8 ‡aIn vitro polymerization of eugenol using a thermal procedure produced a polymer resembling an addition polymer. Elemental analysis indicated some oxidation polymerization had occurred, but considerably less than lignin-like polymers. Solution of this polymer in eugenol, 4%, improved the CS to 9.3 (13.68) MN/m('2) for an experimental cement. Polymer addition, however, was not optimized.
520 8 ‡avalues obtained by polymerization in parentheses: CS 46.1 (69.0) MN/m('2); TS 4.241 (5.24) MN/m('2); E 2600 (4000) MN/m('2); W 22.3 (15.4) 10('-4) mm('3)/mm. Addition of H(,2)PtCl(,6) and acetic acid in combination improved these values over acetic acid alone. The use of H(,2)PtCl(,6) alone produces similar values, however, the setting time was greatly retarded.
520 ‡aThe purpose was to evaluate polymerization as an approach to strengthening zinc oxide-eugenol (ZOE) cements. The polymerization of eugenol provided statistically significant increases in compressive strength (CS), tensile strength (TS), modulus of elasticity (E) and wear resistance compared to the normal chelate setting reaction alone. To produce this reaction chloroplatinic acid, H(,2)PtCl(,6), and acetic acid were added to eugenol and mixed with zinc oxide. Control values are reported followed by
538 ‡aMode of access: Internet.
650 4 ‡aHEALTH SCIENCES, DENTISTRY
899 ‡a39015008092002 ‡bBuhr B 939259
CID ‡a002157210
DAT 0 ‡a20200916121445.0 ‡b20240704000000.0
DAT 1 ‡a20240704120241.0 ‡b2024-07-05T10:03:25Z
DAT 2 ‡a2022-10-02T17:30:02Z
CAT ‡aSDR-MIU ‡cmiu ‡dALMA ‡lprepare.pl-004-008
FMT ‡aBK
HOL ‡0sdr-miu.990021572100106381 ‡aMiU ‡bSDR ‡cMIU ‡f002157210 ‡pmdp.39015008092002 ‡sMIU ‡1990021572100106381
974 ‡bMIU ‡cMIU ‡d20240705 ‡sgoogle ‡umdp.39015008092002 ‡y1981 ‡ric ‡qbib ‡tUS bib date1 >= 1929
974 ‡bMIU ‡cMIU ‡d20240705 ‡sgoogle ‡umdp.39015008092010 ‡ztext ‡y1981 ‡ric ‡qbib ‡tUS bib date1 >= 1929